RAYMARINE EV-200 Power Evolution Autopilot
The Raymarine EV-200 Power Autopilot’s EV sensor core can be installed almost anywhere on your boat – above or below deck. Install upsidedown or off the vessel’s centreline.
Once installed, the Raymarine EV-200 Power Autopilotsetup is easy, with a simple Dockside Wizard to guide you through the process.
Raymarine EV-200 Power Autopilots are installed on vessels around the world from large yachts, to smaller fishing boats and RIBs. Watch our video of Evolution users sharing their experience.
Fuel efficient
Raymarine EV-200 Power Autopilot steers so accurately they will save fuel and get you to your destination faster.
Robust
The Raymarine EV-200 Power Autopilot enclosure is fully sealed and built to IPX6 waterproofing standards
3 Response level modes
Tailor the Raymarine EV-200 Power Autopilot to your liking by selecting either Leisure, Cruising or Performance mode.
In the Box
EV-1 Sensor
ACU-200 Processor
p70R control head
Evolution cabling kit
Installation hardware
Documentation
Raymarine EV-200 Power Autopilot Features:
Evolution Ai for superior performance
No calibration required
Use with any Type 1 or Type 2 Drive Unit (sold separately)
12V or 24V DC operation
SeaTalkng Network Capable
ACU-200 auxiliary power to SeaTalkng network
Includes p70Rs Autopilot Controller
Raymarine EV-200 Power Autopilot Includes:
EV-1 Sensor Core
p70Rs Autopilot Control Head
ACU-200 Actuator Control Unit (Includes the M81105 Rotary Rudder Reference)
Evolution Cabling Kit
EV Unit O-Ring Pack (set of 2)
Wall Mounting Bracket
The EV Sensor Core
At the center of every Evolution system is the intelligent EV sensor core, a 9-axis sensor that monitors vessel motion in all three dimensions. The innovative EV sensor core combines advanced solid-state sensors with the Evolution autopilot processor into a single easy-toinstall housing.
Mount the EV sensor core above or below decks, the rugged enclosure is fully sealed and built to IPX6 and IPX7 waterproofing and submersion standards.
The EV-1 is designed for Evolution mechanical and hydraulic autopilot systems. SeaTalkng networking enables a single cable connection for power and data to the Evolution ACU (actuator control unit) and extended SeaTalkng and NMEA2000 networks.
Features:
Precision monitoring of heading, pitch, roll, and yaw allowing the autopilot to evolve instantly as sea conditions and vessel dynamics change
Flexible installation options
Mount above or below deck
Simple SeaTalkng connectivity to the control head and ACU
Solid state sensor technology delivers dynamic accuracy to within 2 degrees in all conditions
Fast and reliable heading data for MARPA, radar overlay, and heading modes on Raymarine multifunction displays
p70Rs Autopilot Control Head
The p70Rs has a convenient rotary control knob and support for multiple autopilot modes including Auto, standby, trolling patterns, and track mode from your GPS or chartplotter.
Features:
LightHouse user interface is simple and quick to use
Wide 160 viewing angles
Start up wizard helps you configure the pilot quickly and easily
Anti-reflective coating for improved visibility in bright sunlight
Low power – typically 132mA/1.6W – 27% less than ST70 at x4 measured brightness
Supported autopilot modes: Auto; Standby; Pattern; Track; Wind Vane; Power Steer and Jog Steer
Simple system and group dimming/illumination
Support for multiple data sources
SeaTalkng/NMEA2000 and SeaTalk1 connectivity (no bridging required)
ACU-200 Autopilot Control Unit (ACU)
The rugged ACU (Actuator Control Unit) delivers reliable autopilot drive power and also provides power to the SeaTalkng bus. Choose the ACU that fits your steering system type.
Support Drive Units
Type 1 or Type 2 Drive Unit (sold separately)
Evolution Cabling Kit
1 x SeaTalkng Power Cable (0.4m)
1 x SeaTalkng Backbone Cable (5m)
1 x SeaTalkng Spur Cable (0.4m)
1 x SeaTalkng 5-way Connector Block
2 x SeaTalkng T-piece Connector
2 x SeaTalkng Terminator
Specifications
Vessel: Small to mid-sized vessels
Steering Type: Hydraulic or mechanical
Display: 3.5″ Color LCD
Control Type: p70r rotary
Processor: ACU 200: 12 or 24VDC, 15 Amp continuous
Rudder Feedback: Rudder feedback optional
Compass: EV-1 Sensor
Drive Unit: Not Included
Remote Options: C & E Series Network Displays, multiple control heads
Interface: SeaTalk-ng (NMEA 2000)
Dimensions: Control head: 4.3″W x 4.5″H x 1.6″D; Processor: 11.2″W x 8.3″H x 2.5″D; Wt: 4.9 lbs.
Warranty: Two Year, with extra year after on-line registration
